12 kW genuinely available, eight reinforced 16 A outputs and a fixed terminal block connection: the sizing for a complete server room. The batteries are replaced without cutting power to the equipment.
Usable power of 12 kW
8 C19 outputs, reinforced 16 A outlets for power-hungry equipment
Terminal block connection: fixed wiring, to be installed by an electrician
Single-phase 230 V or three-phase 400 V input depending on the installation
Sine wave output
Hot-swappable batteries, without shutting down the connected devices
Additional battery modules to extend runtime
PowerView LCD display: load, battery level and remaining runtime
Very high-power online UPS for critical infrastructure: online double-conversion, 12 kW / 15 kVA, 6U stack/rack chassis. Technology & protection: power is fully regenerated, continuously — the equipment never touches the mains, with no transfer time. Maximum protection against power cuts, surges, voltage fluctuations and electrical noise. Power: 15 kVA for 12 kW — sized for server racks and industrial equipment. Ports: terminal-block connection (fixed wiring by an electrician); single-phase or three-phase input depending on the installation. Management: RS-232 serial port, network management card and a port for network access; emergency power off (EPO) switch. Additional battery modules and hot-swap batteries, replaceable without switching off your equipment. LCD display (PowerView module): shows load, battery level and remaining runtime — monitor the UPS without any software. Designed, for example, for data centres and critical infrastructure. Remember to check how much power your equipment draws and to choose the capacity according to the runtime you need.
Be the first to review this product and help other customers.
Write a review
Frequently asked questions about this product
Does the Smart-UPS RT 15 kVA connect via sockets or a terminal block?
Via a terminal block on the input: either 3-wire single-phase or 5-wire three-phase, depending on the installation. It is fixed wiring, to be done by an electrician, with a 100 A input circuit breaker to be provided.
What outputs does the Smart-UPS RT 15 kVA offer?
Eight heavy-duty 16 A C19 outlets, two IEC jumpers, and two terminal block outputs — one 3-wire, the other 5-wire. C19 is the format used by high-current equipment, blade chassis and storage arrays.
How much does the Smart-UPS RT 15 kVA weigh?
247.7 kg, for a 432 × 773 × 533 mm chassis. At this weight, installation requires handling equipment, a floor that has been checked and clear access all the way to the room: this is the first point to sort out.
Can the batteries be changed without shutting down the equipment?
Yes, they are hot-swappable, without switching off the connected devices. Additional battery modules can also extend the runtime, and a full recharge takes 2 h 30.
Why does 15 kVA give only 12 kW?
The power factor is 0.8: 12 kW actually available. Compare this figure in watts with the combined consumption of the server room — it is what determines the load the UPS can carry.
What input voltage range does the UPS accept?
160 to 280 V, with an auto-sensed frequency of 40 to 70 Hz. In double conversion, the output remains a sine wave whatever the quality of the incoming grid.
How is the Smart-UPS RT 15 kVA monitored?
Through a DB-9 RS-232 serial port, a 10/100 RJ-45 network port for remote monitoring, and a SmartSlot. A PowerView LCD screen on the front panel shows the load, battery level and remaining runtime.
Can the UPS be shut off in an emergency?
Yes, an emergency power-off (EPO) switch is provided: in a single action, it cuts power to everything connected. This is a common requirement in a regulated electrical room.
Is the APC Smart-UPS RT 15 kVA new and under warranty?
Yes, new equipment, with the invoice serving as the warranty document, for 2 years. Its batteries are maintenance-free sealed lead-acid, and the UPS accepts a 230 V single-phase or 400 V three-phase input depending on the installation. The datasheet covers the rest.
Network management card already fitted, with environmental monitoring: it is administered and raises alerts remotely. 9 minutes of runtime at 50% load (10 kW), extendable with battery packs.
•Runtime: 9 min at 50% load (10 kW), 5 min at 70% (14 kW)
•An external battery pack is included; runtime remains extendable
•Network Management Card 3 pre-installed, with environmental monitoring
Fifteen minutes of runtime at full load, internal batteries included. Dust filter and conformal-coated boards: it is made for demanding premises, on a three-phase 400 V input tolerated from 304 to 477 V.
Power factor of 1: all 8 000 W stated are available. Ten battery-backed outlets, four of them heavy-duty 16 A, and the Web/SNMP network management card is included.
•8 000 W usable output (power factor of 1)
•6 C13 outlets, the format used by computer and server power cords, all battery-backed
•4 C19 outlets, heavy-duty 16 A, also battery-backed
Ten battery-backed outlets, four of them heavy-duty 16 A, for 4 500 W usable and around 11 minutes of runtime at half load (2 250 W). The Web/SNMP management card is included.
•4 500 W usable output (power factor of 0.9)
•Around 11 minutes of runtime at 50% load (2 250 W), 7 minutes at 70% (3 150 W)
•6 C13 outlets, the format used by computer and server power cords, all battery-backed
16 kW genuinely available and around 14 minutes of runtime at half load, extendable with up to four battery cabinets. Terminal block input and output, for hard-wired infrastructure.
•16 kW usable output
•Around 14 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
A free-standing tower on castors, with an LCD screen showing the load, the battery status and the voltages. Around 16 minutes of runtime at half load, extendable with up to four battery cabinets.
•Around 16 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
Three reinforced 16 A outlets for power-hungry hardware, eight server outlets, and batteries that are changed without cutting the power. Under 40 dB at one metre, in a rack as in a tower.
•8 C13 outlets: the format of computer and server power cords
All the power available in watts: 10,000 W usable, as many as the VA. Around 7 minutes of runtime at half load (5000 W) to shut down a full rack cleanly, in only 4U.
For a whole infrastructure: 9 minutes of runtime at half load (5000 W) and 5 minutes at 70%, the time it takes to switch over to a generator. 94% efficiency at full load and internal bypass.
A maintenance bypass supplied as standard allows the UPS to be replaced without shutting down the equipment it powers. Around 15 minutes of runtime at half load (4 000 W), extendable with four battery cabinets.
•Around 15 minutes of runtime at half load (4 000 W)
•Runtime extendable with one to four external battery cabinets
•Internal batteries included: 2 strings of 7 Ah, expandable to 3 for more runtime
•Three-phase 400 V input and output, also 380 or 415 V
In stock
92 399 DHincl. VAT92 399,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
In stock
65 999 DHincl. VAT65 999,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
In stock
51 199 DHincl. VAT51 199,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
49 999 DHincl. VAT49 999,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
•Internal bypass and maintenance bypass as standard
In stock
41 999 DHincl. VAT41 999,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
•3 C19 outlets: reinforced 16 A outlets for power-hungry equipment
•Terminal block input: fixed wiring, to be installed by an electrician
Network management card already fitted, with environmental monitoring: it is administered and raises alerts remotely. 9 minutes of runtime at 50% load (10 kW), extendable with battery packs.
•Runtime: 9 min at 50% load (10 kW), 5 min at 70% (14 kW)
•An external battery pack is included; runtime remains extendable
•Network Management Card 3 pre-installed, with environmental monitoring
All the power available in watts: 10,000 W usable, as many as the VA. Around 7 minutes of runtime at half load (5000 W) to shut down a full rack cleanly, in only 4U.
A maintenance bypass supplied as standard allows the UPS to be replaced without shutting down the equipment it powers. Around 15 minutes of runtime at half load (4 000 W), extendable with four battery cabinets.
•Around 15 minutes of runtime at half load (4 000 W)
16 kW genuinely available and around 14 minutes of runtime at half load, extendable with up to four battery cabinets. Terminal block input and output, for hard-wired infrastructure.
•16 kW usable output
•Around 14 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
A free-standing tower on castors, with an LCD screen showing the load, the battery status and the voltages. Around 16 minutes of runtime at half load, extendable with up to four battery cabinets.
For a whole infrastructure: 9 minutes of runtime at half load (5000 W) and 5 minutes at 70%, the time it takes to switch over to a generator. 94% efficiency at full load and internal bypass.
Doubling the runtime comes down to one extra battery cabinet: 9 minutes at half load become 23 minutes. The 16 12 V batteries are chosen and ordered separately.
Four U in a rack and a battery recharged in 3 hours: it is ready to go again quickly after a cut. Around 11 minutes of runtime at half load (3000 W) and 7 minutes at 70%.
Nineteen minutes of runtime at half load, extended to fifty with an additional battery cabinet. The 16 12 V batteries are chosen and ordered separately.
Up to four external battery modules extend the 10.5 minutes of runtime at half load. The 2U rack mounting kit, the output cords and the USB cable are included.
•Runtime: 10.5 min at half load, 3.5 min at full load
•Runtime extendable by up to 4 external battery modules
