Eight outlets in the server power cord format and two reinforced 16 A outlets, for 5,400 W usable and around 11 minutes of runtime at half load (2,700 W). Enough to close a rack down cleanly.
Usable power of 5,400 W (0.9 power factor)
Runtime of around 11 minutes at 50% load (2,700 W), 8 minutes at 70%
8 C13 outlets, the format of computer and server power cords
2 C19 outlets, reinforced 16 A for power-hungry equipment
Output also available on a terminal block
2 controllable outlet groups: cut the non-essential first
USB port and RS-232 serial port for automatic server shutdown
Slot for an SNMP network card, remote monitoring
Internal bypass: power still flows even if the UPS develops a fault
Hot-swappable batteries from the front panel
Runtime extendable with external battery cabinets, detected automatically
Multilingual graphic LCD display, rotatable for rack or tower
A high-end online UPS, convertible between rack and tower: online double conversion, 6000 VA / 5400 W, 3U format. Technology & protection: power is fully and continuously regenerated — your servers are never exposed to the mains, with zero transfer time. Complete protection against outages, surges, voltage fluctuations and electrical noise. Power: 6000 VA for 5400 W of real power (0.9 power factor) — almost all of the rated power is available in watts. Runtime: about 11 minutes at half load (2700 W), 8 minutes at 70%. Ports: 8 C13 outlets + 2 heavy-duty C19 outlets + terminal block. Active cooling (≈ 45 dB), ideally installed in a technical room. Designed, for example, for servers, storage or critical network racks. LCD display: shows load, battery level and remaining runtime at a glance — so you can monitor the UPS without any software. Remember to check how much power your equipment draws and to choose the rating according to the runtime you need.
Be the first to review this product and help other customers.
Write a review
Frequently asked questions about this product
How long does the 9SX 6000i run on battery?
11 minutes at 50% load, i.e. 2700 W, and 8 minutes at 70%, i.e. 3780 W. Runtime can be extended with external battery cabinets, which the UPS detects automatically as soon as they are connected.
What are the controllable outlet groups on the 9SX for?
To cut non-essential loads first: two outlet groups can be controlled separately, so you can switch off secondary equipment during an outage and reserve the whole battery for critical machines. That is extra runtime without changing UPS.
What outputs does the 9SX 6000i offer?
Eight C13 outlets, two heavy-duty C19 outlets and a terminal block output. The input, for its part, is on a terminal block only: it is fixed wiring, to be done by an electrician.
Does this 6 kVA UPS really deliver 5400 W of usable power?
Yes, thanks to its power factor of 0.9: 6000 × 0.9 = 5400 W. The 9SX also has input power factor correction, which limits the pollution it sends back into the upstream supply.
Can the batteries be changed without shutting down the servers?
Yes, they are hot-swappable from the front panel. Charging uses either the ABM method — which only recharges when necessary and gives up to 50% longer service life — or temperature compensation, as you choose.
Is the network management card included?
No: it is only supplied as standard on the Netpack versions of the range. On this model, the slot is free and accepts a Network-MS (SNMP), ModBus-MS or dry-contact Relay-MS card, to be ordered separately.
Can the 9SX 6000i be installed in a rack or as a tower?
Both: a 3U convertible chassis, with a rack-mount kit included, and a multilingual graphic LCD screen that can be rotated to suit the position. Allow for 440 × 130 × 685 mm and 48 kg.
How do you connect the 9SX 6000i to a monitoring system or a server?
Via a USB port or an RS-232 port — which cannot be used simultaneously —, four dry contacts on DB9, a mini terminal block for remote on/off control and an emergency power off. A slot also takes an optional network card.
Does service continue if the UPS fails?
Yes, an internal bypass lets mains power through to the equipment even if the UPS fails or there is a short circuit downstream. This is what stops a UPS failure from becoming a rack failure.
Is the Eaton 9SX 6000i (9SX6KIRT) new and under warranty?
Yes, new equipment, with the invoice serving as the warranty document, for 2 years on a standard-exchange basis — installation, removal and connection to the load remaining the customer's responsibility. It stays below 45 dB. The datasheet covers the rest.
A free-standing tower on castors, with an LCD screen showing the load, the battery status and the voltages. Around 16 minutes of runtime at half load, extendable with up to four battery cabinets.
•Around 16 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
•Internal bypass and maintenance bypass as standard
Three reinforced 16 A outlets for power-hungry hardware, eight server outlets, and batteries that are changed without cutting the power. Under 40 dB at one metre, in a rack as in a tower.
•8 C13 outlets: the format of computer and server power cords
Ten battery-backed outlets, four of them heavy-duty 16 A, for 4 500 W usable and around 11 minutes of runtime at half load (2 250 W). The Web/SNMP management card is included.
•4 500 W usable output (power factor of 0.9)
•Around 11 minutes of runtime at 50% load (2 250 W), 7 minutes at 70% (3 150 W)
•6 C13 outlets, the format used by computer and server power cords, all battery-backed
A maintenance bypass supplied as standard allows the UPS to be replaced without shutting down the equipment it powers. Around 15 minutes of runtime at half load (4 000 W), extendable with four battery cabinets.
•Around 15 minutes of runtime at half load (4 000 W)
•Runtime extendable with one to four external battery cabinets
16 kW genuinely available and around 14 minutes of runtime at half load, extendable with up to four battery cabinets. Terminal block input and output, for hard-wired infrastructure.
•16 kW usable output
•Around 14 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
Built for the server room: 8 C13 outlets, 2 C19 and a hardwired output, 98% efficiency in eco mode and runtime expandable with external battery modules. Hot-swappable batteries, managed over USB, RS232 or an optional network card.
Three-phase online UPS rated 20 kVA for 20 kW, configurable as 3:3, 3:1 or 1:1. Supplied without batteries: 32 to 40 12 V blocks inside, or external cabinets. Up to 98.5% efficiency in ECO mode, maintenance bypass and touch screen.
All the power available in watts: 10,000 W usable, as many as the VA. Around 7 minutes of runtime at half load (5000 W) to shut down a full rack cleanly, in only 4U.
For a whole infrastructure: 9 minutes of runtime at half load (5000 W) and 5 minutes at 70%, the time it takes to switch over to a generator. 94% efficiency at full load and internal bypass.
•3-wire terminal block connection: fixed wiring, to be installed by an electrician
In stock
28 599 DHincl. VAT28 599,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
A 6000 W online double-conversion UPS for a server fleet, a storage array or a network room: pure sine wave, power factor 1, up to 95.5% efficiency. Rack or tower, manual maintenance bypass, expandable runtime.
A 6000 W online double-conversion UPS for a server fleet, a storage array or a network room: pure sine wave, power factor 1, up to 95.5% efficiency. Rack or tower, manual maintenance bypass, expandable runtime.
Three reinforced 16 A outlets for power-hungry hardware, eight server outlets, and batteries that are changed without cutting the power. Under 40 dB at one metre, in a rack as in a tower.
•8 C13 outlets: the format of computer and server power cords
Power factor of 1: all 8 000 W stated are available. Ten battery-backed outlets, four of them heavy-duty 16 A, and the Web/SNMP network management card is included.
•8 000 W usable output (power factor of 1)
•6 C13 outlets, the format used by computer and server power cords, all battery-backed
Built for the server room: 8 C13 outlets, 2 C19 and a hardwired output, 98% efficiency in eco mode and runtime expandable with external battery modules. Hot-swappable batteries, managed over USB, RS232 or an optional network card.
Ten battery-backed outlets, four of them heavy-duty 16 A, for 4 500 W usable and around 11 minutes of runtime at half load (2 250 W). The Web/SNMP management card is included.
•4 500 W usable output (power factor of 0.9)
•Around 11 minutes of runtime at 50% load (2 250 W), 7 minutes at 70% (3 150 W)
Online double-conversion UPS rated 6000 VA for 6000 W, with no internal battery: it runs on one to four external cabinets. With one 2U cabinet of 16 HR09122F batteries, it holds 17 min at half load and 5 min at full load.
Four U in a rack and a battery recharged in 3 hours: it is ready to go again quickly after a cut. Around 11 minutes of runtime at half load (3000 W) and 7 minutes at 70%.
Every outlet is battery-backed, with around 11 minutes of runtime at half load (990 W). Automatic and manual internal bypass, LCD screen and a detachable 2.44 m cord supplied.
A 6000 VA / 6000 W double-conversion online UPS delivered complete: 2U power module, 3U SRV240RLBP-9A external battery pack and rail kit. Terminal-block connection, pure sine wave output, 94 % efficiency and runtime expandable up to four packs.
•Around 11 minutes of runtime at 50% load (990 W), 7 minutes at 70% (1 386 W)
•All output outlets are battery-backed
•C13 outlets in the format used by computer and server power cords, C19 outlets heavy-duty at 16 A
In stock
18 199 DHincl. VAT18 199,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
•6000 VA / 6000 W, double-conversion online
•5U rack: 2U UPS and 3U battery pack
•SRV240RLBP-9A battery pack supplied
In stock
24 299 DHincl. VAT24 299,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
An online double-conversion 2U rack or tower UPS: 1800 W of pure sine wave power for a server and its rack, efficiency up to 94%, hot-swappable batteries and runtime extendable with an external pack.
