Thirty minutes of runtime at 50% load (2,700 W), enough to ride out a cut without stopping production. Three-phase 400 V input, single-phase output, external maintenance bypass included.
5,400 W usable output (power factor of 0.9)
Around 30 minutes of runtime at 50% load (2,700 W), 20 minutes at 70%
Three-phase 380/400/415 V input, single-phase output
4 C19 outlets, heavy-duty 16 A for power-hungry equipment
Output also available on a terminal block
External maintenance bypass included
Runtime extendable with external battery cabinets, detected automatically
USB port and RS-232 serial port for automatic server shutdown
A high-end, high-power online UPS for server rooms: online double conversion, 6 kVA / 5400 W. Technology & protection: power is fully and continuously regenerated — the equipment is never exposed to the mains, with zero transfer time. Maximum protection against outages, surges, voltage fluctuations and electrical noise. Power: 6 kVA for 5400 W of real power (0.9 power factor) — almost all of the rated power is available in watts. Runtime can be extended with external battery cabinets. Ports: 4 heavy-duty C19 outlets + terminal block; three-phase input connection. USB port, serial port and slot for an SNMP network card. Active cooling (≈ 48 dB), to be installed in a technical room. LCD display: shows load, battery level and remaining runtime at a glance — so you can monitor the UPS without any software. Designed, for example, for server racks, network equipment or industrial applications. Remember to check how much power your equipment draws and to choose the rating according to the runtime you need.
305 - 480 V without derating (175 - 480 V with derating)
Battery type
Sealed, lead-acid (12 V/9 Ah)
Battery management
ABM® or temperature-compensated charging method (user-selectable), automatic battery test, deep discharge protection, external battery pack detection
Interface port
1 USB port, 1 RS232 port (cannot be used simultaneously), 4 dry contacts (DB9), 1 remote on/off control mini terminal block, 1 emergency power off, 1 DB15 paralleling connector
User interface
Multilingual graphic LCD screen
Audible alarm
Yes
Power management software
Eaton Intelligent Power
Weight (kg)
88 kg
Dimensions (W x D x H) (mm)
440 x 700 x 260 mm
Technology
On-line
Power (VA)
6,000 VA
Voltage stabiliser
Yes
Box contents
9PX power module
9PX battery module
External maintenance bypass
USB cable
Serial cable
1 battery cable with communications for automatic battery cabinet recognition
2 brackets for tower mounting
Tower mounting link plate
Safety guide
Quick start
Technical specifications (continued)
Communication card slot
1 slot for Network-MS, ModBus-MS or Relay-MS card (optional)
Rack height
6U
Transfer/switching time
0 ms (continuous double conversion)
Bypass
Internal bypass + HotSwap MBP maintenance bypass as standard
Audible noise
< 48 dBA
Power factor (ratio)
0.9
Input power factor
Input power factor correction (PFC), ratio not published by the manufacturer
Output frequency
50/60 Hz auto-selecting, frequency converter as standard
Be the first to review this product and help other customers.
Write a review
Frequently asked questions about this product
Does the 9PX 6000i require a three-phase supply?
Yes: the input is three-phase at 380, 400 or 415 V, on a terminal block, while the output remains single-phase. The accepted range extends from 305 to 480 V. The three-phase circuit at the distribution board is therefore the first point to confirm with an electrician.
How long does the 9PX 6000i run on battery?
30 minutes at 50% load, i.e. 2700 W, and 20 minutes at 70%. That is exceptionally long for this power rating: enough to ride out an entire outage without stopping production, rather than simply shutting down cleanly.
Is the maintenance bypass supplied with the 9PX 6000i?
Yes, an external maintenance bypass is supplied with the unit. It lets you remove the UPS for servicing or replacement without cutting power to the protected equipment — that is what the HotSwap suffix in the model designation refers to.
Can two 9PX 6000i units be run in parallel?
Yes: a DB15 connector is provided for paralleling two UPSs, which lets you either double the available power or build in redundancy. Few UPSs in this range allow it.
What outputs does the 9PX 6000i offer?
Four heavy-duty 16 A C19 outlets, plus a terminal block output for fixed wiring. C19 is the format for high-current equipment: high-power servers, storage arrays, blade chassis.
Does this 6 kVA UPS deliver 5400 W of usable power?
Yes, thanks to its power factor of 0.9: 6000 × 0.9 = 5400 W. The 9PX also has input power factor correction, which limits the harmonics sent back into the upstream three-phase supply.
What weight and space should you plan for?
88 kg for an assembly measuring 440 × 260 × 700 mm: this model combines a power module, a battery module and the maintenance bypass. Plan the handling accordingly, and a floor that can bear this load.
Can runtime be extended beyond 30 minutes?
Yes, with external battery cabinets that the UPS detects automatically — the supplied battery cable in fact includes the communication link needed for this detection.
How do you monitor the 9PX 6000i and shut down the servers?
Via a USB port or an RS-232 port — not simultaneously —, four dry contacts on DB9, a mini terminal block for remote control and an emergency power off. A slot accepts a Network-MS, ModBus-MS or Relay-MS network card, not included except on Netpack versions.
Is the Eaton 9PX 6000i (9PX6KIBP31) new and under warranty?
Yes, new equipment, with the invoice serving as the warranty document, for 2 years. It delivers a sine wave output, stays below 48 dB and manages its batteries with ABM technology, which only recharges them when necessary. The datasheet covers the rest.
Ten battery-backed outlets, four of them heavy-duty 16 A, for 4 500 W usable and around 11 minutes of runtime at half load (2 250 W). The Web/SNMP management card is included.
•4 500 W usable output (power factor of 0.9)
•Around 11 minutes of runtime at 50% load (2 250 W), 7 minutes at 70% (3 150 W)
•6 C13 outlets, the format used by computer and server power cords, all battery-backed
16 kW genuinely available and around 14 minutes of runtime at half load, extendable with up to four battery cabinets. Terminal block input and output, for hard-wired infrastructure.
•16 kW usable output
•Around 14 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
A free-standing tower on castors, with an LCD screen showing the load, the battery status and the voltages. Around 16 minutes of runtime at half load, extendable with up to four battery cabinets.
•Around 16 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
Three reinforced 16 A outlets for power-hungry hardware, eight server outlets, and batteries that are changed without cutting the power. Under 40 dB at one metre, in a rack as in a tower.
•8 C13 outlets: the format of computer and server power cords
Power factor of 1: all 8 000 W stated are available. Ten battery-backed outlets, four of them heavy-duty 16 A, and the Web/SNMP network management card is included.
•8 000 W usable output (power factor of 1)
•6 C13 outlets, the format used by computer and server power cords, all battery-backed
•4 C19 outlets, heavy-duty 16 A, also battery-backed
All the power available in watts: 10,000 W usable, as many as the VA. Around 7 minutes of runtime at half load (5000 W) to shut down a full rack cleanly, in only 4U.
For a whole infrastructure: 9 minutes of runtime at half load (5000 W) and 5 minutes at 70%, the time it takes to switch over to a generator. 94% efficiency at full load and internal bypass.
A maintenance bypass supplied as standard allows the UPS to be replaced without shutting down the equipment it powers. Around 15 minutes of runtime at half load (4 000 W), extendable with four battery cabinets.
•Around 15 minutes of runtime at half load (4 000 W)
•Runtime extendable with one to four external battery cabinets
Four U in a rack and a battery recharged in 3 hours: it is ready to go again quickly after a cut. Around 11 minutes of runtime at half load (3000 W) and 7 minutes at 70%.
Built-in network card: monitoring and control happen remotely, from the company network. 1980 W genuinely available and ten output sockets, two of them reinforced 16 A, in a chassis meant for the rack.
49 999 DHincl. VAT49 999,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
•Internal bypass and maintenance bypass as standard
In stock
41 999 DHincl. VAT41 999,00 DHincl. VAT
Delivery everywhereDelivered all over Morocco
•3 C19 outlets: reinforced 16 A outlets for power-hungry equipment
•Terminal block input: fixed wiring, to be installed by an electrician
Three reinforced 16 A outlets for power-hungry hardware, eight server outlets, and batteries that are changed without cutting the power. Under 40 dB at one metre, in a rack as in a tower.
•8 C13 outlets: the format of computer and server power cords
•3 C19 outlets: reinforced 16 A outlets for power-hungry equipment
•Terminal block input: fixed wiring, to be installed by an electrician
Four U in a rack and a battery recharged in 3 hours: it is ready to go again quickly after a cut. Around 11 minutes of runtime at half load (3000 W) and 7 minutes at 70%.
Nineteen minutes of runtime at half load, extended to fifty with an additional battery cabinet. The 16 12 V batteries are chosen and ordered separately.
Floor-standing, 68.5 cm high and 54 kg: the tower version, for when there is no rack. Around 11 minutes of runtime at half load (3000 W) and 94% efficiency at full load.
Twenty minutes of runtime at half load (2 400 W), extended to several hours with up to four external battery cabinets. The standard maintenance bypass allows the unit to be swapped without shutting down the equipment.
•Around 20 minutes of runtime at half load (2 400 W)
A maintenance bypass supplied as standard allows the UPS to be replaced without shutting down the equipment it powers. Around 15 minutes of runtime at half load (4 000 W), extendable with four battery cabinets.
•Around 15 minutes of runtime at half load (4 000 W)
16 kW genuinely available and around 14 minutes of runtime at half load, extendable with up to four battery cabinets. Terminal block input and output, for hard-wired infrastructure.
•16 kW usable output
•Around 14 minutes of runtime at half load
•Runtime extendable with one to four external battery cabinets
A free-standing tower on castors, with an LCD screen showing the load, the battery status and the voltages. Around 16 minutes of runtime at half load, extendable with up to four battery cabinets.
For a whole infrastructure: 9 minutes of runtime at half load (5000 W) and 5 minutes at 70%, the time it takes to switch over to a generator. 94% efficiency at full load and internal bypass.
All the power available in watts: 10,000 W usable, as many as the VA. Around 7 minutes of runtime at half load (5000 W) to shut down a full rack cleanly, in only 4U.
